 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MP3414 1.8a,1mhz, synchronous, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 1 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. the future of analog ic technology description the MP3414 is a high-efficiency, synchronous, current?mode, step-up converter with output disconnect. the MP3414 can start up from an input voltage as low as 0.8v to provide inrush current limiting, and output short-circuit protection. the integrated, p-channel, synchronous rectifier improves efficiency and eliminates the need for an external schottky diode. the pmos disconnects the output from the input when the part shuts down. this output disconnect feature allows the output to be completely discharged, thus allowing the part to draw a 1 a supply current in shutdown mode. the 1mhz switching frequency allows for smaller external components, while the internal compensation and the soft-start minimize the external component count: these feature help to produce a compact solution for a wide current load range. the MP3414 features an integrated power mosfet that supports up to a 4v output and a typical 1.8a peak switching current. the MP3414 is available in a small 8-pin tsot23 package. features ? up to 96% efficiency ? 0.8v low voltage start-up ? 0.6v-to-4v input range ? 1.8v-to-4v output range ? internal synchronous rectifier ? 1mhz fixed-frequency switching ? 35 a quiescent current ? 1 a shutdown current ? current-mode control with internal compensation ? true output disconnect from input ? v in >v out down mode operation ? high efficiency under light-load conditions ? very small external components ? inrush current limiting and internal soft- start ? over-voltage protection ? short-circuit protection ? tsot23-8 package applications ? battery-powered products ? personal medical devices ? portable media players ? wireless peripherals ? handheld computers and smartphones a ll mps parts are lead-free, halogen free, and adhere to the rohs directive. fo r mps green status, please visit mps website under quality assurance. ?mps? and ?the future of analog ic technology? are registered trademarks o f monolithic power systems, inc. typical application MP3414 in en 1 8 c in 10f l 3.3h 3 sw vin on off pgnd 4 agnd 6 r1 365k fb 2 7 c out 47f vout r2 210k out 0 10 20 30 40 50 60 70 80 90 100 0.01 0.1 1 10 100 1000
MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 2 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. ordering information part number* package top marking MP3414dj tsot23-8 see below * for tape & reel, add suffix ?z (e.g. MP3414dj?z); for rohs-compliant packaging, add suffix ?lf (e.g. MP3414dj?lf?z) top marking acm: product code of MP3414dj y: year code package reference top view tsot23-8 MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 3 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. absolute maxi mum ratings (1) sw pin, out pin ........................ -0.5v to +6.5v all other pins ................................... -0.5v to +6v continuous power dissipation (t a = 25c) (2) ................................................................. 1.25w junction temperature ............................... 150c lead temperature .................................... 260c storage temperature .............. ?65c to +150c recommended operating conditions (3) start-up voltage v st ........................... 0.8v to 4v supply voltage v in ............................. 0.6v to 4v v out .................................................... 1.8v to 4v operating junction temp. (t j ). -40c to +125c thermal resistance (4) ja jc tsot23-8 .............................. 100 ..... 55 ... c/w notes: 1) exceeding these ratings may damage the device. 2) the maximum allowable power dissipation is a function of the maximum junction temperature t j (max), the junction-to- ambient thermal resistance ja , and the ambient temperature t a . the maximum allowable continuous power dissipation at any ambient temperature is calculated by p d (max)=(t j (max)- t a )/ ja . exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. internal thermal shutdown circuitry protects the device from permanent damage. 3) the device is not guaranteed to function outside of its operation conditions. 4) measured on jesd51-7 4-layer board. MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 4 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. electrical characteristics v in = v en = 1.8v, v out = 3.3v, t a = 25c, unless otherwise noted. parameters symbol condition min typ max units minimum startup voltage v st 0.8 1.0 v operating input voltage v in 0.6 4 v output voltage adjust range v out 1.8 4.0 v quiescent current i qns v en =v in =1.8v, v out =3.3v, no load, measured on out pin 35 50 a shutdown current i sd v en =v out =0v, measured on in pin 1 3 a in under-voltage lockout v uvlo v in rising 0.4 0.5 0.6 v operation frequency f sw 0.8 1.0 1.2 mhz feedback voltage v fb 1.19 1.21 1.23 v feedback input current i fb v fb =1.25v 1 50 na nmos on-resistance r nds on 110 m ? nmos leakage current i nlk v sw =6.5v 0.1 1 a pmos on-resistance r pds on 120 m ? pmos leakage current i plk v sw =6.5v, v out =0v 0.1 1 a maximum duty cycle d max 89 95 % startup current limit i st limit 0.75 a nmos current limit i sw limit 1.5 1.8 a en input high level v en_h 0.8 v in v en input low level v en_l 0.2 v in v en input current i en connect to v in 10 na thermal shutdown (5) 150 c over temperature hysteresis (5) 20 c notes: 5 guaranteed by design, not tested MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 5 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. typical performanc e characteristics performance waveforms are tested on the evaluation board in the design example section. v in = 1.8v, v out = 3.3v, l = 3.3h, t a = 25c, unless otherwise noted. MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 6 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. typical performanc e characteristics (continued) performance waveforms are tested on the evaluation board in the design example section. v in = 1.8v, v out = 3.3v, l = 3.3h, t a = 25c, unless otherwise noted. MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 7 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. pin functions pin # name pin function 1 in input supply. requires bypass capacitor. 2 out output node. source of the internal synchrono us rectifier. place the output capacitor as close as possible between out and pgnd. 3 sw output switch node. connect the inducto r to sw to complete the step-up converter. 4 pgnd power ground. reference ground of the regulated output voltage. 5 nc no connection. 6 agnd analog ground. 7 fb feedback. connect to the tap of an external resistive volt age divider from the output to fb to set the output voltage. 8 en enable input. turns regulator on or off. logic high (>0.8v in ) turns on the regulator. it is internally pulled up to in pin through 1.5m ? resistor. MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 8 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. block diagram driver and control logic + - current sense amplifier oscillator sw out agnd ea fb en bias and voltage ref 1.21v slope comp pwm comp start-up mode control vin body control vdd in enable + - + - + v better soft start fb ovp clamp thermal control + - zero current cross comp out pgnd pgnd hs ls figure 1: functional block diagram MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 9 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. operation the MP3414 is a 1mhz, synchronous, step-up converter housed in a compact tsot23 package with true output disconnect. able to operate at low-input voltages of less than 0.8v, the device features fixed-frequency current- mode pwm control for exceptional line and load regulation. internal soft-start and loop compensation simplify the design process and minimize the external components. the internal low-r ds(on) mosfets combined with power save mode operation enable the device to maintain high efficiency over a wide current- load range. synchronous rectifier the MP3414 integrates an n-channel and a p- channel mosfet to realize a synchronous rectifier. replacing the traditional schottky diode with a low-r ds(on) pmos improves efficiency. in a conventional synchronous rectifier, the pmos body diode is forward- biased, and the current flows from v in to v out . the MP3414 allows for true output disconnect by eliminating the body diode, and prevents battery depletion when the converter shuts down. to prevent excessive inductor current, the pmos synchronous rectifier only functions when v out > (v in +200mv). start-up when en is on, the MP3414 starts up with a linear charge period. during this linear charge period, the rectifier pmos turns on until the output capacitor charges to v in ?200mv; the pmos current is limited during this period to around 750ma to avoid inrush current. this circuit also helps to limit the output current under short circuit conditions. after the linear charging period, the device starts switching. if v out remains below 1.7v, the part then works in free-running mode; in this mode, the device works in open loop at a fixed 500khz switching frequency, the duty cycle depends on the input-output ratio, and the switching current is limited to 1.2a to avoid the start-up current inrush. the internal soft-start (ss) does not take charge and continues to rise following the fb voltage during the linear charging and free- running period. once the output voltage reaches 1.7v, the normal closed-loop operation initiates, v out starts to rise under the control of ss, and the current limit goes to 1.8a. it then works either in boost mode or down mode depending on v in and v out . table 1 lists the operation modes during start up. table 1: operation mode during start-up sequence v out MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 10 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. quiescent power dissipation as well as switching power loss. the out pin voltage- monitoring circuit and error amplifier with loop compensation for peak-current? mode control remain active. the output ripple, which is usually around 1% peak to peak, can be reduced by increasing the output capacitance and also by adding a small feed-forward capacitance (around 10pf). the MP3414 operates from psm to pwm mode depending on the load, which varies with the input voltage, inductor value, and the output capacitor value. under-voltage lockout under-voltage lockout prevents device startup when v in falls below 0.5v while in operation and the battery is being discharged. error amplifier the error amplifier (ea) is an internally- compensated amplifier. the ea compares the internal 1.21v reference voltage against v fb to generate an error signal. the output voltage of MP3414 could be adjusted from 1.8v to 4v by connecting fb to the tap of an external voltage divider from v out to ground, as per the following equation: r1 out r2 v1.21v(1) ??? (1) set r1 and r2 as large as possible to achieve a low quiescent current. usually, select an r1 value larger than 300k for good stability and transient balance. current sensing lossless current sensing converts the nmos switch current signal to a voltage that can be summed with the internal slope compensator. the difference between this summed signal and the error amplifier output provides control over the peak current through the pwm. peak switch current is limited to approximately 1.8a, independent of input or output voltage. the switching current signal is blanked for 60ns to enhance noise rejection. thermal protection the device has an internal temperature monitor if the die temperature exceeds 150c, the switches turn off. once the output drops below 1.7v, it will turn on. output disconnect and inrush limiting the MP3414 is designed to allow true output disconnect by eliminating the internal pmos rectifier?s body diode conduction. this feature allows v out to go to 0v during shutdown and draw 0a from the input source. it also allows for inrush current limiting at start-up, which minimizes surge currents at the input supply. note that to optimize output disconnect, exclude the external schottky diode between sw and v out . to minimize voltage overshoot on the sw pin due to stray inductance, keep the output filter capacitor as close as possible to the v out pin and use very low esr/esl ceramic capacitors tied to a clean ground plane. short-circuit protection unlike most step-up converters, the MP3414 allows for short circuits on the output. in the event of a short circuit, the device first turns off the nmos when the sensed current reaches the current limit. the device then enters a linear charge period with the current limited as with the start-up period. in addition, the thermal regulation circuit further controls the input current if the die temperature rises above 150c. down mode (v in >v out ) operation the MP3414 will continue to regulate the output voltage even when the input voltage exceeds the output voltage. this is achieved by terminating the switching at the synchronous pmos and applying v in statically on its gate. this ensures that the slope of the inductor current will reverse while current flows to the output. since the pmos no longer acts as a low-impedance switch in this mode, power dissipation increases within the ic to cause a sharp drop in efficiency. limit the maximum output current to maintain an acceptable junction temperature. MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 11 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. application information component selection input capacitor selection low esr input capacitors reduce input switching noise and reduce the peak current drawn from the battery. it follows that ceramic capacitors are also a good choice for input decoupling and should be located as close as possible to the device. add a ceramic capacitor larger than 10 f in parallel with a 100nf ceramic capacitor close to the ic. output capacitor selection the output capacitor requires a minimum capacitance value of 22 f at the programmed output voltage to ensure stability over the full operating range. a higher capacitance value may be required to lower the output ripple and also the transient response. low esr capacitors, such as x5r- or x7r-type ceramic capacitors, are recommended. assuming that the esr is zero, estimate the minimum output capacitance to support the ripple in the pwm mode as. o out(max) in(min) o sout(max) i(v v ) c fv ? v ?? ? ?? (2) where, v out(max) = maximum output voltage v in(min) = minimum input voltage i o =output current f s = switching frequency ? v= acceptable output ripple additional output capacitance may also be required for applications where v in v out to reduce ripple in psm mode and to ensure stability in pwm mode, especially at higher output load currents. inductor selection the MP3414 can use small surface-mount inductors due to its 1mhz switching frequency. inductor values between 1.5 h and 4.7 h are suitable for most applications. larger values of inductance will allow slightly greater output current capability (and lower the psm threshold) by reducing the inductor ripple current. increasing the inductance above 6.8 h will increase component size while providing little improvement in output current capability. the minimum inductance value is given by: in(min) out(max) in(min) out(max) l s v(v v) l 2v ? if ?? ? ??? (3) where ? i l is the acceptable inductor current ripple the inductor current ripple is typically set at 30% to 40% of the maximum inductor current. high-frequency ferrite-core inductor materials reduce frequency-dependent power losses and improve efficiency compared to cheaper powdered-iron cores. the inductor should have low dcr (inductor series resistance without saturated windings) to reduce the resistive power loss; further reducing the dcr will significantly improv e efficiency when dcr< MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect MP3414 rev 1.05 www.monolithicpower.com 13 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. typical application circuits figure 3: boost circuit. v in =1.2v, v out =1.8v. MP3414 ? 1.8a, 1mhz, synchrono us, step-up converter with output disconnect notice: the information in this document is subject to change wi thout notice. users should warra nt and guarantee that third party intellectual property rights are not infringed upon w hen integrating mps products into any application. mps will not assume any legal responsibility for any said applications. MP3414 rev. 1.05 www.monolithicpower.com 14 3/30/2018 mps proprietary information. patent protec ted. unauthorized photocopy and duplication prohibited. ? 2018 mps. all rights reserved. package information tsot23-8 |
Price & Availability of MP3414
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |